How to Select a Robotic Gripper for Small-Part Assembly

November 20, 2026

The robot gets the attention, but the gripper decides whether your application works. In our recent webinar with Doosan Robotics, Top 3 Cobot Applications: Where Collaborative Robots Deliver the Fastest ROI, one point kept coming up: the part and the gripper have to match. Get that right, and a cobot can pick, place, and assemble small parts reliably shift after shift. Get it wrong, and you’ll fight dropped parts, misaligned insertions, and constant tweaking.

This guide covers how to choose a gripper for small-part assembly, from gripper type and grip force to payload, safety, and changeover.

New to cobots? Start with our webinar recap:

Why Small-Part Assembly Is a Great Cobot Fit

Small-part assembly checks every box Lance Douglas of Doosan Robotics laid out for a fast-ROI cobot application:

  • It’s repetitive. The same pick, orient, and insert motion, hundreds or thousands of times a shift.
  • It’s measurable. Cycle time, first-pass yield, and scrap are easy to track before and after.
  • It’s hard to staff. Fine, repetitive hand work leads to fatigue, inconsistency, and turnover.
  • It fits the cobot envelope. Small parts are light, well within the payload of compact cobots like the Doosan M0609.

Because these parts are small and tolerances are tight, the gripper often matters more than the arm.

Step 1: Start With the Part, Not the Gripper

Before looking at catalogs, document every part the gripper will handle:

  1. Size and weight, including the heaviest and smallest part in the family
  2. Material and surface: metal, plastic, glass-filled, painted, oily, porous, or finished surfaces that can’t be marked
  3. Geometry: flat faces, cylinders, flanges, or features you can grip on or locate against
  4. Fragility: whether the part can tolerate clamping force, or needs light or controlled force
  5. Tolerances: how precisely the part must be positioned for the next step, such as pressing a pin or inserting a connector
  6. Part variety: how many SKUs the same gripper must handle, and how often you change over

If you’re running a high-mix line, that last point may drive every other decision.

Step 2: Choose the Right Gripper Type

Gripper type Best for Watch out for
Electric parallel gripper Most small-part pick-and-place and assembly; programmable force, position, and speed Higher upfront cost than pneumatic
Pneumatic parallel gripper High-speed, high-force, simple open/close tasks Needs compressed air routed to the arm; force control is limited
Angular gripper Tight spaces, or when jaws need to swing clear of the part Grip point shifts as jaws close
Three-jaw / centric gripper Round parts, shafts, and bushings that need self-centering Less versatile for flat or irregular parts
Vacuum (suction) gripper Flat, smooth parts like covers, panels, labels, and PCBs Porous, oily, or textured surfaces; small contact areas
Soft / adaptive gripper Delicate or irregular parts and mixed-part families Lower precision for tight-tolerance placement
Magnetic gripper Ferrous parts like washers, brackets, and stampings Residual magnetism; only works on ferrous material

For most cobot small-part assembly, an electric parallel gripper is the default starting point. It needs no compressed air on the arm, and it lets you program grip force and jaw position, so one gripper can handle multiple parts. It also plugs neatly into the cobot’s tool flange and teach pendant software.

Step 3: Calculate the Grip Force You Need

Too little force and parts slip during fast moves. Too much and you dent, scratch, or crack them. The gripper’s job is to hold the part against gravity and the acceleration of the robot’s motion.

Friction grip (flat fingers squeezing the part) is the most common case. A standard estimate is:

F = (m × (g + a) × S) ÷ (μ × n)

  • F = required gripping force (N)
  • m = part mass (kg)
  • g = gravity (9.81 m/s²)
  • a = robot acceleration (m/s²)
  • S = safety factor (commonly 2)
  • μ = coefficient of friction between fingers and part
  • n = number of jaws in contact

Example: A 0.25 kg steel part, moved at 5 m/s², with a safety factor of 2, μ = 0.2, and two jaws: F = (0.25 × 14.81 × 2) ÷ (0.2 × 2) ≈ 18.5 N

Form-fit fingers, shaped to cradle or wrap the part, hold it mechanically instead of relying on friction. They need far less force, which is gentler on delicate parts and safer around people. When you can, design fingers that form-fit the part.

Step 4: Match Stroke, Precision, and Finger Design

  • Stroke: The jaws must open wide enough to clear your largest part (plus approach clearance) and close far enough to grip your smallest. Short-stroke grippers are faster. Long-stroke grippers handle more part variety.
  • Repeatability: For assembly, the gripper’s repeatability has to support your tolerance stack-up together with the robot’s.
  • Centering: Self-centering jaws locate the part consistently in the gripper, which matters for insertions.
  • Custom fingertips: Off-the-shelf jaws rarely fit small parts perfectly. Machined or 3D-printed fingertips with locating features, chamfers, or soft inserts often make the difference. As Lance noted in the webinar, swapping fingertips is usually easy, and many grippers can handle multiple parts with no changes at all.

Step 5: Check Your Payload Budget

A cobot’s rated payload covers everything on the end of the arm: the gripper, fingers, any tool changer, cabling, and the part. Center of gravity matters too. A heavy gripper that sticks out far from the flange reduces usable payload.

For small parts, the gripper often weighs more than the part, so compact, lightweight grippers keep you on smaller, lower-cost arms. In Doosan model numbers, the first two digits are payload in kilograms. A Doosan M0609, for example, handles 6 kg. Small plastic parts typically fit there, while heavier metal components may call for an H-series arm.

Step 6: Design for Collaborative Safety

During the webinar Q&A, an attendee asked a great question: How do you make sure the tool or the product doesn’t hit someone? The cobot arm is designed to be safe, but the gripper and the part are part of the safety picture, too.

Here’s what Lance recommended:

  • Limit clamp force. Ask whether the gripper could injure a finger if it closed on it. Many grippers are rated for collaborative use, with limited closing force.
  • Avoid sharp edges. Choose grippers and fingers with smooth, rounded edges and no pinch points or sharp corners.
  • Look at the part, too. A sharp or pointed part can cause injury even if the gripper is safe.
  • Add safeguarding when needed. If the application requires a heavier clamp that can’t be considered collaborative, use an area safety scanner to slow or stop the robot, or disable the gripper function, when someone approaches.
  • Always run a risk assessment. Collaborative applications are typically assessed using ISO/TS 15066 guidance on force and pressure limits. Your risk assessment should cover the entire cell, not just the arm.

Step 7: Plan for Integration and Changeover

  • Power and communication: Electric grippers typically connect through the cobot’s tool flange I/O or a fieldbus such as Modbus. Check for native plug-ins that let you control the gripper directly from the teach pendant.
  • Air supply: If you choose pneumatic, plan how air will route along the arm without snagging during motion.
  • Tool changers: If one gripper can’t handle every part, a quick changer lets you swap tools in seconds, either manually or automatically.
  • Sensing: Jaw position feedback confirms a part was gripped and can flag the wrong part or a missed pick.
  • Compliance for insertion: Tight-tolerance insertions benefit from a little “give.” Doosan cobots have torque sensors in every joint, so the robot can feel resistance and adjust during insertions without a separate compliance device.

Step 8: Don’t Forget Part Presentation

The best gripper in the world can’t pick a part it can’t find. In the webinar, part presentation came up as one of the biggest factors in how long a cell can run unattended. How parts arrive (trays, fixtures, feeders, or conveyors with vision) affects your gripper choice, approach angle, and finger design.

Gripper Selection Checklist

  • Part sizes, weights, materials, and tolerances documented for every SKU
  • Gripper type matched to part geometry and surface
  • Grip force calculated with a safety factor, and form-fit fingers used where possible
  • Stroke covers the full range of part sizes
  • Gripper + fingers + part within the cobot’s payload and center-ofgravity limits
  • Clamp force, edges, and part hazards reviewed for collaborative safety
  • Power, I/O, and teach pendant integration confirmed
  • Changeover plan in place: fingertips, quick changer, or programmable stroke
  • Part presentation method defined
  • Process proven with sample parts before full deployment

FAQs

For most applications, an electric parallel gripper. It needs no compressed air, offers programmable force and position, and integrates easily with cobot software. Vacuum grippers are a strong choice for flat, smooth parts.

Not necessarily. Programmable-stroke electric grippers and well-designed fingertips can often handle a family of similar parts. For very different parts, quick changers make swapping tools fast.

Check whether the gripper is rated for collaborative applications, which typically means limited closing force and rounded edges. Then run a risk assessment for the full cell, including the part itself.

Yes. iAutomation has demo robots our team can bring on site, and Doosan offers trials and a loaner program for qualifying applications. Testing with your actual parts is the best way to confirm grip, cycle time, and placement accuracy.

iAutomation is a hightech distributor with engineering and value-added services, not a systems integrator. We supply cobots, grippers, safety products, power, and I/O, and provide applications engineering support. When your project needs a full custom cell, we can connect you with the right integration partner.

Find the Right Gripper for Your Application

iAutomation carries Doosan collaborative robots along with the grippers, safety, power, and I/O products that complete the application, including Festo and OnRobot. Our applications engineers can help you match the right gripper to your parts, and we can bring a demo robot to your facility.

Talk to a Specialist Today!